You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
{{ message }}
Repository navigation
solidcore: a curved Setback that no fill certifies up to twice its setbacks is refused untyped, naming no size #16398
Found while measuring #13832 step 5 (#16370): a curved Setback that no fill certifies up to twice the rule's setbacks is refused as an untyped failure that names no size.
Repro (test hip_roof_apex_of_unequal_rounds_is_refused_as_data in solidcore/crates/solidcore/tests/issue_2343_curved_setback.rs on #16370, #[ignore]d because it fails on main):
Part: a hip roof with one curved slope. It is the intersection of a prism along x (section: z >= 0, the plane z = 6 + 3y/4 for y < 0, and the circle of radius 5 about (y, z) = (-3, 2)) and a prism along y (the triangle (-6, 0), (0, 6), (6, 0) in (x, z)).
The apex V = (0, 0, 6) is a convex vertex of four edges. Its faces are three planes and a convex cylinder.
Round the four apex edges 1, 1.25, 1.5 and 1.75 together (fillet_setback_beside_curved_faces on).
classify_setback takes the corner as a Setback, with rule setbacks [1.575, 1.875, 2.25, 2.625].
No G1 fill up to degree 9 certifies at 1x or at the growth's first trial, 2x. At degrees 6 to 9 the QP solves, but every net fails the exact curvature certificate (certified_sign / t_nonneg checks). Degree 5 is infeasible, and 3 and 4 have no affine solution.
grow_curved returns SetbackRefusal::no_room("... no setbacks up to twice the rule's ...", Some(0.0)) with no .typed(...). The session then returns SolidError::Failed { operation: "blend::fillet_executive::session::finish", reason: Blend(Failed("the fillet body is not built")), status: 1001 }, with fit_setback() = 0.
The same path serves the asked form ("no setback up to twice {a} ..."), e.g. asked 4.0, and three-round corners.
Expected: a typed SolidError::BlendRefused that carries the cause and its site (the vertex). If no size can be named, say so in the type: §7.3 asks that a refusal names the size that fits, from the cause.
Related gap (MEASURED, not a wrong body):
Rounds 1, 1.1, 1.2, 1.3 are refused the same way.
1, 1, 1, 1 and 1, 1, 1, 1.25 build and grade: check_brep level 2, seams G1 to 4.3e-12 rad against the exact normals, convex, contained.
The planar twin, with the cylinder replaced by the plane z = 6 - 3y/4, builds 1, 1.25, 1.5, 1.75.
So four mildly unequal rounds beside a cylinder never certify, because the QP's sector rows do not imply the net certificate there. The refusal is on the conservative side. Whether a certified fill exists for these radii is not shown.
Activity
solidcore: test the curved Setback with four rounds, and the cone gro…
solidcore: test the curved Setback with four rounds, and the cone gro…
solidcore: test the curved Setback with four rounds, and the cone gro…
solidcore: test the curved Setback with four rounds, and the cone gro…
solidcore: curved Setback with four rounds, and the cone grown vs pla…